Shopping Cart

CycoActive
GPS Packages

Complete systems
designed for your
motorcycle

Garmin
GPS Receivers

Accessories

Mount Systems

Mount Gallery

Software

GPS Power and Interface Cables

---

For GPSs used on motorcycles, the most common problem is vibration induced shutdown. All of this discussion below pertains to use of a GPS in a vibrating environment. It is most important on 2-strokes, singles, and some twins, less on 3, 4, 6 cyl motorcycles, unless the motorcycle is often used at very high RPMs. For more info, see battery tips.

Garmin GPSs have a computer chip running inside (some have an Intel 386 and others have an ARM) which can get confused and shutdown or freeze if the power supply is not smooth. If your motorcycle does not have a LARGE battery, see battery tips. If you have hardwired your GPS to the motorcycles 12VDC supply and you are still getting shutdown, do these three things:

1) Eliminate any possible source of disconnection under vibration. No spring-type fuses allowed, use blade-type. Note that inside the Garmin power cord, there is a spring-type fuse holder, this is a problem. We recommend that you tap directly into the motorcycle's 12vDC supply if possible.

2) If you have installed a cigarette lighter socket on the bike, that connection itself is a likely source of disconnection. Use tape to immobilize it, and use dielectric grease on the contacts.

3) Use dielectric grease on every connection, especially if you elect to retain the spring-type fuse holder inside the Garmin cigarette lighter adapter. Take the fuse out and put dielectric grease on every little part in the power path. Do it now, before the sparking contaminates all of the connection points. Once you've contaminated the metal coatings on the terminals (or sanded it off), the contamination gets worse. Use Dielectric grease from the beginning.

If you are using an eTrex, eMap, GPS12 or Rino, then you MUST retain the voltage reducer on the Garmin cig-lighter cord, and you must put Dielectric grease on all the connections in the power path. The circuitboard on the G10203 adapter must be hardened for motorcycle use especially for singles and twins. Also see GCE3VC and 065-0116 for eMap/eTrex/Geko.

If you intend to run the GPS on its internal batteries, please see battery tips.

---

Power and Interface Cables for Garmin Receivers with round 4-pin power connectors

Availability: In Stock

The Motorcycle 12v Hardwire Kit, for GPS III, V, SP, SPIII, 176, 176C, 60, 76 includes these items:

• GPS Power cord
• Waterproof fuse holder
• 2A fuses plus a spare
• Dielectric grease
• Powercord end holder
• Battery terminals
• Splice connector for large fuseholder to small red wire

This kit contains everything you need to connect your GPS to your motorcycle and protect your connections from vibration: a 12V power cord (5.5 ft long), battery terminal connectors, a blade-type fuse kit with two 2A fuses, a cap for the plug, and a small container of dielectric grease.

Fits the GPSs listed below:

• GPS II, II+, III, III+, V
• GPS12XL, 12MAP, 12CX (not GPS12)
• GPS 60, 72, 76
• GPSMAP 60, 60C, 60CS, 60Cx, 60CSx
• GPSMAP 76, 76S, 76C, 76CS, 76Cx, 76CSx
• GPSMAP 96, 96C
• GPSMAP 176, 176C, 196
• StreetPilot, StreetPilot Color
• StreetPilot III

Availability: In Stock

This will power your GPS from any common cigarette lighter. This power cable uses Garmin's 4-pin round power & interface connector found on many of their GPS units.

• GPS II, II+, III, III+, V
• GPS12XL, 12MAP, 12CX (not GPS12)
• GPSMAP 60C, 60CS, 60Cx, 60CSx
• GPSMAP 76, 76MAP, 76S
• GPSMAP 76C, 76Cx 76CS 76CSx
• GPSMAP 176, 176C
• StreetPilot, StreetPilot Color, StreetPilot III

Availability: In Stock

This interface cable has the traditional Garmin round 4-pin plug on one end and a 9-pin serial (RS-232) connector on the other. There is no connection for power. 3 wires inside (Data in, Data out, and ground), no provision for power.

Plug your Garmin GPS into your PC serial port to download maps and create routes and waypoints. Fits these GPSs:

• GPS 38, 40, 45, 45XL
• GPS II, II+, III, III+, V
• GPS 12, 12XL, 12MAP, 12CX
• GPSMAP all 60 series, C, CS, Cx, CSx
• GPSMAP all 72, 76 series, 76MAP, 76S
• GPSMAP all 76C, CS, Cx, CSx
• GPSMAP 176, 176C
• StreetPilot, StreetPilot Color
• StreetPilot III

Availability: In Stock

Many Garmins have the capability to transfer waypoints, tracks, and routes from one GPS to another. This can be done in the woods, away from computers. Fits most Garmins that have the standard Garmin 4-pin round plug.

NOTE: Even though it fits the Garmin GPS V, the :software system of the GPS V is not able to transfer data directly to/from another GPS . For the GPS V, you must use a computer to transfer data between GPS units.

ALSO, many of the newer GPSs have a much larger tracklog capacity than older models. If you try to transfer a tracklog from a newer GPS to an older GPS, it will probably cut the tracklog at the point where the older GPS is "full".

Availability: In Stock

This cable has both the 9-pin serial (RS-232) interface connector and a cigarette lighter power adapter. Fits, GPS II/III/V, GPS 60, 76, 176, Streetpilot, StreetPilotIII.

Power your GPS from a 12v cigarette lighter supply while doing map and data transfers from your PC. Perfect for using connecting the GPS to your PC to enable the "Moving Map" function which is part of Garmin's MapSource software.

Availability: Not Normally Stocked

This adapter has a cigarette lighter power connection with a small speaker attached. The cable attaches to the round power connector on the StreetPilot III and the audio output connector so you can hear the voice prompts. This is a replacement item for the one included with the original unit.

Availability: In Stock

The Garmin AC Adapter provides 12V DC for a wide variety of Garmin GPS units.

This AC Adapter provides 12v DC for these Garmin GPS units:

• GPS III
• GPS III+
• GPS V
• StreetPilot
• GPS 45
• GPSMAP 60 series
• GPSMAP 76 series
• GPSMAP 176, 176C.

This will NOT work for the new 2600 and 2700 StreetPilot GPS units.

Power and Interface Cables for Garmin StreetPilot 2600 and 2700 models

Availability: In Stock

This kit contains everything you need to connect your GPS to your motorcycle: a 12V power cord (5.5 ft long), battery terminal connectors, a blade-type fuse kit with two 2A fuses, and a small container of dielectric grease.

This kit is for the Garmin GPS 2610, 2620, 2720, 2730, and the new 2820. This kit provides power only, it has no provision for sound output.

For a kit with sound output connections, please see item G10495-2 listed under Additional Information.

Availability: In Stock

Plugs into the Garmin GPS 2610, 2620, 2720, 2730, 2820

• Supplies power
• Mono audio output jack (for 2.5 mm mono plug)
• Includes glass fuse 1.0A (AGC type)
• 80+ inches long

Availability: In Stock

Allows use of Garmin StreetPilot series 26xx, 27xx, 28xx away from the motorcycle. With this useful power pack you can program your GPS unit, (and many other 12v units away from your vehicle. In conjunction with our ZA adapter (# 030-0016) you can even charge your mobile phone (if 1.5V alkalines used) The battery pack is supplied in a stainless steel housing. Weighs approx. 270 grams (without batteries)

• Provides about 5 hours GPS runtime
• Can use alkaline or rechargeable AA batteries
• Has support receptacle for 26xx and other Garmin cradles
• includes BMW plug outlet (can be adapted to cig-lighter with 030-0017)
• Can operate other small items such as cellphone chargers
• Includes 10 AA Alkaline cells
• 15v output if Alkaline batteries are used, 12v output with NiMh used
• CABLES NOT included

Availability: In Stock

This accessory is a replacement for the 12/24-volt adapter cable with external speaker that came with your StreetPilot 2610 or 2620. It allows you to power your unit from a cigarette lighter and hear the voice prompts. So if you need a new one, don't delay. You'll be lost without it.

This item is designed for a car environment and will need some waterproofing for motorcycle use.

Power and Interface Cables for Garmin GPSMAP 276C and 376C

Availability: In Stock

The Motorcycle 12v Hardwire Kit for Garmin 276C, 376C includes these items:

• 5ft Power Cable
• Waterproof Fuse Holder
• 2 2A Fuses
• 2 Battery Crimp connectors
• Bullet connector
• Dielectric Grease

This kit contains everything you need to connect your GPS to your motorcycle: a 12V power cord (4 ft long), battery terminal connectors, a blade-type fuse kit with two 2A fuses, and a small container of dielectric grease.

This kit is for the Garmin GPSMAP 276, 376, 378 and 478. This kit provides power only, it has no provision for sound output.

For a kit with sound output connections, please see item G10587.

• Genuine Garmin power cable
• Rugged waterproof fuse holder
• Everything you need

Availability: In Stock

Fits the Garmin GPSMAP 276, 376, 378 and 478. This cord functions as a 12/24-volt power adapter cable and has an external speaker built into the cigarette plug housing to dictate GPS guidance directions while driving. It allows you to power your unit from a cigarette lighter and hear the voice prompts. This is an excellent accessory to purchase if you have City Select or City Navigator software for your 276C or 376C and want to use the unit in your car.

This item is designed for a car environment and is not waterproof. Unless you have a Goldwing or other very smooth ride, this may not be the best choice on a bike.

Availability: In Stock

This bare-wire cable contains all the power and data leads that are available for the Garmin GPSMAP 276, 376, 378 and 478. The power line is fused and a fuse is included.

This is a replacement part for the cable included with the 276C.

Availability: In Stock

This is a simple cigarette lighter power adapter for the Garmin GPSMAP 276, 376, 378 and 478. There are no connections to the audio output or other signals.

Availability: In Stock

Rechargeable lithium battery offering 5-15 hours of use (depending on backlight settings)

Replacement or use as a spare. Fits Garmin GPSMAP 276, 376, 378 and 478.

Availability: In Stock

This Power Audio Cable has a 2.5mm female socket built into the cord. Power and ground connections are bare wires (black and red). Compatible with Touratech helmet speakers Part Number 065-0337.

Fits 376C also, but note that 376C has a stereo 3.5mm audio jack built into the case. Also works for Garmin 378 and 478.

• Supplies power
• Mono audio output jack (for 3.5 mm mono plug)
• Includes glass fuse 1.0A (AGC type)
• 80+ inches long

Availability: In Stock

Power Audio cable with BMW style power plug for Garmin GPSMAP 276, 376, 378 and 478.

Fits 376C - but note that 376C has a 3.5mm audio jack built-in to the case.

• 2.5mm Mono audio socket
• Total cable length is about 40 inches

Power and Interface Cables for Garmin Quest and Quest 2

Availability: Backordered

Quest cradle by GARMIN. Consists of a Quest Cradle, cable, adapter ONLY. Requires RAM mount system to attach to a motorcycle. Suggested RAM mount is GRSP3H, or for the ball only, use GRAB.

• built-in voltage reduction circuit for hardwire to 12vDC motorcycle battery
• Has a safety latch feature
• Audio ouput is 3.5mm mono
• Cable length 72 inches

Availability: In Stock

This Touratech Power & Audio Cable only works in the Touratech Mounts for the Garmin Quest GPS units.

For Garmin Quest only, with BMW plug and audio plug. Has an in-line voltage reduction circuit. It is for motorcycle use, designed to withstand vibration and is weatherproof. Can be hardwired into your bike if desired.

NOTE: This 5v power cable is for the Garmin Quest only, and is designed to be permanently mounted to TOURATECH mounts 065-0089, 0090, 0091, 0092. It DOES NOT fit properly on the GARMIN cradles or the RAM cradle. Caution: Do not use this 5volt cord on 3v GPSs (such as eTrex, eMap, and ForeTrex).

• Reduction circuit: 12vDC to 5vDC
• 2.5mm Mono audio output

Availability: In Stock

Fits Garmin Quest AND Touratech Mounts only. With BMW plug and audio plug. Has an in-line voltage reduction circuit. Can be hardwired into your bike as long as the voltage reduction circuit remains.

Reduces 12vDC to 5vDC

length: 40 inches

voltage reduction module is 12 inches from Quest end

NOTE: This 5v power cable is for the Garmin Quest only, and is designed to be permanently mounted to TOURATECH mounts 065-0089, 0090, 0091, 0092. It DOES NOT fit properly on the GARMIN cradles or the RAM cradle. Caution: Using this 5v cord on a 3v GPS (such as eTrex, eMap, and ForeTrex) will damage the GPS.

General Power and Wiring Accessories

Availability: In Stock

Use Dielectric Grease on the terminals inside your battery case to help keep your contacts clean and in good operating order.

• protects electrical connections under vibration
• provides corrosion protection
• travel size can be re-sealed see photo
• See more info regarding GPS battery problems on motorcycles

Availability: In Stock

This Vinyl Weather Cap will keep your Garmin Round Power Cord out of the weather and protect the exposed terminals from coming into contact with something they shouldn't.

• fits power cord of: III, V, 60, 76, StreetPilot and StreetPilot III, 176
• fits power cords G10085 and GC12V
• keeps power cord end clean and dry
• keeps dust off if you are using dielectric grease on power cord end
• has a vent hole
• see photo links at right

Availability: In Stock

This heavy-duty, waterproof fuse holder snaps securely closed and won't leak under any conditions or location. Uses the well-known "superseal" method to cinch closed under pressure to prevent water entry . The cover has a tab with a mounting hole for a screw or zip-tie. This fuseholder is properly isolated from both water and vibration making it appropriate for motorcycles, off-road vehicles and military applications.

The fuseholder comes with two 20-amp fuses so you can use this kit to wire in heated clothing, auxillary lights or most other electrical accessories on your bike.

The fuseholder is made with heavy duty 12-gauge copper wire and is rated for up to 30-amps at 32v. Using the included 20-amp fuses in a 12v wiring system (common on motorcycles and non-military vehicles) this kit can take a draw of 240 watts.

• Completely weather proof
• 8-inch of wire each side
• Orange 12 ga GPT heavy duty wire
• Two 2A fuses included
• Capacity: up to 30A at 32V
• Accepts any standard Blade fuse

Availability: In Stock

This Cigarette Lighter Socket is good quality and includes a weatherproof cap, wiring with an inline fuse (and the cigarette lighter insert).

• Easy to install
• For 7/8" to 1" hole
• Panel mount up to 3/16" thick

All the rest

Availability: Backordered

12v Cigarette lighter adapter for Garmin eMap, Geko and eTrex Greyscale

• 12vDC input, 3vDC output
• Does NOT fit eTrex Legend C and Vista C

IMPORTANT NOTE: This adapter is extremely susceptible to vibration, often failing within the first few minutes of use on a single-cylinder motorcycle. For motorcycle applications we recommend G10203V (vibration-modified by CycoActive).

Availability: Backordered

This allows you to power your eTrex Color model GPS from the cigarette lighter in your car. It will work on your bike, but these units are definitely not waterproof.

Availability: Not Normally Stocked

This PC Interface Cable has a 9-pin serial (RS232) connector on one end and the eMap or eTrex connector on the other.

This will NOT work with the new eTrex C models such as the eTrex Vista C or Legend C.

Availability: In Stock

part# gce3Vc

run-time of C-cells is 3 times longer than AA cells

recommended for motorcycle use to prevent vibration-induced shutdown and contamination of the internal AA terminals. This is a simpler option than using G10203V + g12vOUT + 030-0021.

cable approx 24 inches long

fits eMap, eTrex, Geko

keeps your AA batteries fresh for the trail.

better for continuous use of backlight at night.

the GPS automatically switches over to the internal AA batteries if the cable is unplugged.

FOUR-wire cable. which you can modify for data transfer.

Not required to have batteries inside the GPS.

available in kit form -(you attach the cord to the battery pack)

On dirtbikes, carry it in a Glovebox above the headlight.

Does NOT fit eTrex Legend C and Vista C

Availability: In Stock

Cable and battery case (you assemble)

• Red to red (+3v)
• black to black (neg)
• brown and white data wires are not used.

Availability: In Stock

Availability: In Stock

This is the G10203, modified by CycoActive for better vibration resistance.

For Garmin eMap, and greyscale eTrex ONLY. This inexpensive modification is recommended for ALL motorcycle use. G10203 un-modified, will not survive on a single-cylinder motorcycle or 2-cyl motorcycle for more than a couple days. Does NOT fit color eTrex.

• 12vDC to 3vDC converter
• eMap
• eTrex greyscale

Availability: Backordered

Power supply not susceptible to vibration problems of the Garmin product (G10203). In-line 12vDC-to-3vdc reducer adapts to both Cigarette lighter and BMW plug.

NOTE: for Greyscale eTrex ONLY; does NOT fit eTrex Legend C and Vista C (Color screen)

fits eTrex and Geko perfectly.

For eMap please note----------->
a slight modification may be required.

For eMap, batteries are required for startup. Then the eMap senses external supply and switches to external power

for hardwire applications, the cigarette-lighter end can be cut off as long as the 12v-3v reducer circuit remains inline.

does NOT fit eTrex Legend C and Vista C

Availability: In Stock

Plugs into the bottom right of the iQue

Availability: Backordered

12V Charger for Scala Headsets. Fits into a standard cigarette lighter outlet.

• Works with 12-24v DC
• 45 inch cable (coiled)
• Not waterproof