RAM Handlebar Mount for OLDER Garmin StreetPilot & StreetPilot Color

Part Number: GRSPH

$39.00

Add this
to my Cart

Availability:

This is the RAM Handlebar Mount kit for the Garmin StreetPilot and StreetPilot Color. The kit includes the mount adapter, a medium arm and the U-bolt handlebar mount.

The threaded screw holes in the backside of these older Garmin StreetPilot housings aren't very strong. For motorcycle use on rough roads we recommend that this mount should be epoxied to the GPS case, in addition to the screws. We have heard of good results using "JBWeld".

Power and Wiring Options for the RAM Handlebar Mount for OLDER Garmin StreetPilot & StreetPilot Color

Availability: In Stock

The Motorcycle 12v Hardwire Kit, for GPS III, V, SP, SPIII, 176, 176C, 60, 76 includes these items:

• GPS Power cord
• Waterproof fuse holder
• 2A fuses plus a spare
• Dielectric grease
• Powercord end holder
• Battery terminals
• Splice connector for large fuseholder to small red wire

This kit contains everything you need to connect your GPS to your motorcycle and protect your connections from vibration: a 12V power cord (5.5 ft long), battery terminal connectors, a blade-type fuse kit with two 2A fuses, a cap for the plug, and a small container of dielectric grease.

Fits the GPSs listed below:

• GPS II, II+, III, III+, V
• GPS12XL, 12MAP, 12CX (not GPS12)
• GPS 60, 72, 76
• GPSMAP 60, 60C, 60CS, 60Cx, 60CSx
• GPSMAP 76, 76S, 76C, 76CS, 76Cx, 76CSx
• GPSMAP 96, 96C
• GPSMAP 176, 176C, 196
• StreetPilot, StreetPilot Color
• StreetPilot III

Availability: In Stock

This will power your GPS from any common cigarette lighter. This power cable uses Garmin's 4-pin round power & interface connector found on many of their GPS units.

• GPS II, II+, III, III+, V
• GPS12XL, 12MAP, 12CX (not GPS12)
• GPSMAP 60C, 60CS, 60Cx, 60CSx
• GPSMAP 76, 76MAP, 76S
• GPSMAP 76C, 76Cx 76CS 76CSx
• GPSMAP 176, 176C
• StreetPilot, StreetPilot Color, StreetPilot III

Availability: In Stock

This Cigarette Lighter Socket is good quality and includes a weatherproof cap, wiring with an inline fuse (and the cigarette lighter insert).

• Easy to install
• For 7/8" to 1" hole
• Panel mount up to 3/16" thick

Availability: In Stock

(the smallest BMW plug)
Note: For GPS use this is a great choice. Please see the instl photo. Drill the hole out a little to fit tightly on the G10085 powercord. Note that due to the small size, the ground wire must be soldered to the tab.

Availability: In Stock

If your motorcycle doesn't have a BMW-type accessory socket or if you need an additional BMW socket this will allow you to attach one to the bike on any 7/8" or 1" bar (handlebars, frame, etc.). Kit comes with all mounting hardware and wiring to connect directly to the bike's 12v battery.

For flush-mount applications the plug can be removed from the plastic bracket and installed directly onto a panel, fairing section or flat surface with the proper size hole drilled out.

This is the correct socket to add to the bike if you need to plug in accessories with BMW-style plugs such as our CHALA lamps, heated vests or a battery charger. For attaching devices with a standard cigarette lighter plug use the 030-0017 adapter to plug into this BMW socket.